Advantages of Labo C-Top:

Approved medical device

Two independent and separate incubation chambers;

Parameters (gas flow, temperature) can be adjusted individually

Optimized gassing with premixed gas

Optimized temperature distribution by double heated chamber from top and bottom;

Very fast heating up and recovery times

Reliable humidity system;

Current value of relative humidity is displayed (% rH)

Convenient glass control panel

Space saving

Incubation chambers

Aluminum milled and eloxated

In the lower part:

Slots provide full contact to culture dishes

Adaption for humidity block

Gas inlet

Easy cleaning

Independent, for use with (per chamber):

4 x IVF 4-well dishes 66x66 mm

4 x Petri dishes Ø 60 mm

10 x Petri dishes Ø 35 mm

Temperature

Overall heating from top and bottom

Very homogeneous temperature distribution

Humidity

Humidification by means of humidity block

Reservoir sufficient for 4 days (when gassing with 20 ml/min)

Humidity block autoclavable

Humidity alarm disengageable

Current value of relative humidity is displayed (% rH)

Gassing

Connection of premixed gas (CO2, O2 < 21 %, N2)

Separate measuring and regulation of gas flow for each chamber

Automatic gas purge when closing the chamber

Recovery times

Short recovery times for all parameters through microprocessor controlled regulation

Use of glass panel

Homogeneous glass cover

Sensoric buttons integrated in glass

Image of placements for marking inserted dishes at the glass cover

Easy operation and menu navigation

Lit LCD at working place height

Trouble check system

Optical and acoustic alarm in case of set point deviation or defective sensor

Independent over-temperature protection

Remote alarm

Options

PC software LaboDat+ for documentation of incubator’s parameters

Second gas inlet for use of different gas mixtures for each chamber

Lockable lids

Interfaces

Remote alarm (potential free)

RS485-interface for data logging with optional available PC software LaboDat+

Exterior

Dimensions 403 x 225 x 155 mm (w x d x h)

Weight 8.8 kg

Interior

Two chambers with 0.5 liters each

Mixed load possible

Temperature

Overall heating from top and bottom of each chamber

Range 30 °C - 42 °C from 7 °C above

ambient temperature

Stability / uniformity ± 0.1 °C / ± 0.3 °C

Gassing

Premixed gas

Gas flow adjustable between 20 ml/min and 30 ml/min

Flow rate after opening the lid (automatic gas purge):

250 ml/min for 3 minutes

Power Supply

110 – 230 V AC, 50/60 Hz, 100 VA

Primary pressure for gas 0.8 bar

Ambient temperature 18 °C - 30 °C

Classification

Safety class II

Class IIa for every usage according to EC-Directive 93/42/EEC

EN 61010 conform

Advantages of C60:

Approved medical device

Active sterile humidity:

External water reservoir

Distilled water is vaporized at 120 °C

Minimized risk of contamination

Humidity sensor (rH)

Very fast recovery

CO2 sensor:

Dual beam infrared sensor

Very precise measurement

Very fast recovery

Long-term stable

Direct heating:

Independent six-sided direct heating

Homogeneous temperature distribution in incubation chamber

Very fast recovery

Optional:

O2-control

Subdivided inner glass door with 4 small doors

Lockable front door

Access port

PC software LaboDat+

Exterior Dimensions 510 x 540 x 720 mm (w x d x h)

Interior Chamber volume 60 l

Electro-polished stainless steel

Shelves height adjustable

Temperature Panel heated interior chamber and door

Range 27-42 °C starting 5 °C above ambient temperature

Stability / uniformity ±0.1 °C / ±0.3 °C

Over-temperature alarm 32-47 °C

CO2 control Dual beam infrared sensor

Range 0–10 % CO2

Stability ±0.1 % CO2

O2 control < 21 % (optional) Measurement with galvanic sensor

Connection of N2

Adjustable range 1–21 % O2

Humidity Active sterile humidity generated by vaporizing module at 120 °C

Measuring range 0–98 % rH / range 60–95 % rH

Supply 230 V AC, 50/60 Hz or 115 V AC, 50/60 Hz, 160 W

Inlet pressure for gas 0.8 bar

Ambient temperature 18-30 °C

Classification

Safety class I

Class IIa for all usage according to EC-Directive 93/42/EE

Conform to ENN 61010

Interior

Electro-polished stainless steel with coved corners

Shelves and ductwork easily removable for cleaning purposes

Temperature Panel heated interior chamber and door

Humidity supply

Internal water reservoir

CO₂

Dual beam infrared sensor

Measurements independent from temperature and humidity

Very short recovery times

For all adjustable parameters through optimized microprocessor control

Easy Handling

Menu guided

Backlit LCD display

Foil keypad

Diagnostic system

Optical and acoustical alarm if set point deviation or sensor defect occurs

Door monitoring

Air monitoring

Hardware self-test

Remote alarm

Options

O₂ control: connection for N₂

Interfaces

Remote alarm (potential free)

RS485-interface for data-logging with optional PC software LaboDat+

Advantages of C60:

Approved medical device

Active sterile humidity:

External water reservoir

Distilled water is vaporized at 120 °C

Minimized risk of contamination

Humidity sensor (rH)

Very fast recovery

CO2 sensor:

Dual beam infrared sensor

Very precise measurement

Very fast recovery

Long-term stable

Direct heating:

Independent six-sided direct heating

Homogeneous temperature distribution in incubation chamber

Very fast recovery

Optional:

O2-control

Subdivided inner glass door with 4 small doors

Lockable front door

Access port

PC software LaboDat+

Interior

Electro-polished stainless steel with coved corners

No tools required for quick assembly and disassembly of interior

Temperature

Panel heated chamber and door

Intelligent temperature control system avoids condensation in inner chamber

Active sterile Humidity supply

External water supply container

CO2 control

Dual beam infrared sensor

Measurement independent from temperature and humidity

Fast recovery

For all adjustable parameters through optimized microprocessor control

Easy handling

Menu guided

Large, backlit LCD

Foil keyboard

Diagnostic system Visual and acoustic alarm if set point deviation or sensor defect occurs

Door monitoring

Remote alarm

Options

O2 control: connection of N2

Subdivided inner glass door with 4 small doors

Lockable front door

Access port Ø 30 mm

Interfaces

Alarm contact (potential free)

RS485 interface for connection of optional available PC software LaboDat+

Exterior Dimensions 510 x 540 x 720 mm (w x d x h)

Interior Chamber volume 60 l

Electro-polished stainless steel

Shelves height adjustable

Temperature Panel heated interior chamber and door

Range 27-42 °C starting 5 °C above ambient temperature

Stability / uniformity ±0.1 °C / ±0.3 °C

Over-temperature alarm 32-47 °C

CO2 control Dual beam infrared sensor

Range 0–10 % CO2

Stability ±0.1 % CO2

O2 control < 21 % (optional) Measurement with galvanic sensor

Connection of N2

Adjustable range 1–21 % O2

Humidity Active sterile humidity generated by vaporizing module at 120 °C

Measuring range 0–98 % rH / range 60–95 % rH

Supply 230 V AC, 50/60 Hz or 115 V AC, 50/60 Hz, 160 W

Inlet pressure for gas 0.8 bar

Ambient temperature 18-30 °C

Classification

Safety class I

Class IIa for all usage according to EC-Directive 93/42/EE

Conform to ENN 61010

Advantages of C200:

Approved medical device

Active sterile humidity:

External water reservoir

Disteilled water is vaporized at 120 °C

Minimized risk of contamination

Humidity sensor (rH)

Very fast recovery

CO2 sensor:

Dual beam infrared sensor

Very precise measurement

Very fast recovery

Long-term stable

Direct heating:

Independent six-sided direct heating

Homogeneous temperature distribution in incubation chamber

Very fast recovery

Optional:

O2 control

Subdivided inner glass door with 6 small doors

Lockable front door

Access port

PC software LaboDat+

Interior

Electro-polished stainless steel with coved corners

No tools required for quick disassembly and assembly of interior components

Temperature

Panel heated chamber and door

Intelligent temperature control system avoids condensation in inner chamber

Active sterile Humidity supply

External water supply container

CO2 control

Dual beam infrared sensor

Measurement independent from temperature and humidity

Fast recovery

For all adjustable parameters through optimized microprocessor control

Easy handling

Menu guided

Large, backlit LCD

Foil keyboard

Diagnostic system

Optical and acoustic alarm if set point deviation or sensor defect occurs

Door monitoring

Remote alarm

Options

O2 control: connection for N2 possible

Subdivided inner glass door with 6 small doors

Lockable front door

Access port Ø 30 mm

Interfaces

Remote alarm (potential free)

RS485 interface for connection of optional available PC software LaboDat+

Exterior Dimensions 680 x 690 x 930 mm (w x d x h)

Interior Chamber volume 200 l

Electro-polished stainless steel

Shelves height adjustable

Temperature Panel heated interior chamber and door

Range 27-42 °C starting 5 °C above ambient temperature

Stability / uniformity ±0.1 °C /  0.3 °C

Over-temperature alarm 32-47 °C

CO2 control Dual beam infrared sensor

Range 0–10 % CO2

Stability ±0.1 % CO2

O2 control < 21 % (optional) Measurement with galvanic sensor

Connection of N2

Adjustable range 1–21 % O2

Humidity Active sterile humidity generated by vaporizing module operating at 120 °C

Measuring range 0–98 % rH / adjustable range 60–95 % rH

Supply 230 V AC, 50/60 Hz or 115 V AC, 50/60 Hz, 200 W

Inlet pressure 0.8 bar

Ambient temperature 18-30 °C

Classification Safety class I

Class IIa for all usage according to EC-Directive 93/42/EEC

Conform to EN 61010

Transport incubator for a secure and mobile preservation of specimen, culture media etc.

Secure transport of cells without electric mains and CO2 connection

Factory-aligned parameters: 37 °C and 5 % CO2

Different temperature or CO2 concentration possible (to be advised before order)

Operation at 12 V car voltage possible

Use of different heating blocks

Easy handling and cleaning

Compact Design

Parameters* during transport without connection to electric mains and CO2 bottle:

Time Temp. CO2

0 min 37 °C 5 %

10 min 36.6 °C

4.9 %

30 min 35.5 °C 4.8 %

60 min 34.0 °C 4.7 %

*The measurements relate to an ambient temperature of 23 °C .

Power supply

115 V or 240 V AC, 50/60 Hz

12 V DC with car voltage via adapter cable

Dimensions

Outside: 385 x 245 x 305 mm (l x w x h)

Inside:    approx. 312 x 167 x 140 mm (l x w x h)

Weight

Approx. 4.7 kg

Temperature

Available between 32 °C and 39 °C (to be advised before order)

Accuracy of regulation

± 0.3 °C (measured with heating block REF 10264)

Heating up time

Approx. 2 h

CO2 concentration

5 % (different concentrations possible)

Heating block inside necessary

Connection to CO2 supply with pre-pressure of 0.8 bar necessary

CO2 accuracy ± 0.3 % CO2 (when supplied with CO2 with pre-pressure of 0.8 bar ± 0.05 bar)

Advantages of CellTrans+:

Can also be used as back up in case of incubator or power outage

Temperature adjustable between 30 °C and 42 °C

CO2 adjustable between 0 % and 10 %

Reliable humidity system

Easy handling and cleaning

Compact design

Insert for 16 Falcon tubes of 5ml and 13ml each

Duration with completely charged accumulator:

At 2 °C ambient temperature approx. 4 h

At 10 °C ambient temperature approx. 6 h

At 23 °C ambient temperature approx. 10 h

Interior chamber

Anodized aluminum

Insert: stainless steel

Temperature

Over-all heating of lateral surface, bottom and lid of incubation chamber

Homogeneous temperature distribution

Humidity

Via humidifying disc Ø 50 mm

CO2

Dual beam infrared sensor

Measurements independent of temperature and humidity

Recovery times

Short recovery times for all adjustable parameters through microprocessor controlled regulation

Easy navigation

Menue guided

Backlid LCD

Interfaces

USB interace for data evaluation via PC Software DataVISUAL ’19 (in scope of supply) (Compatible up to Windows 10)

Power supply

100 V – 240 V, 60 W

12 V car cable

Dimensions Exterior:

386 x 251 x 370 mm (l x w x h in mm)

Interior:

ø 160 mm, Height 130 mm, volume approx. 1.7 l

Empty weight approx. 10 kgs.

Temperature control

Control range 30 °C – 42 °C at 3 °C above room temperature

Temperature homogeneity ± 0.2 °C

Temperature stability ± 0.1 °C

CO2 regulation

Control range 0 – 10 % CO2

Control accuracy 0.3 % CO2

CO2 pressure tank

Capacity 0.4 l

Pressure 8 bar

Classification

Safety class I

Conform to EN 61010

Transport Incubator for Safe & Versatile Use

•Factory-aligned temperature at 37 °C

•Different temperature possible (to be advised before order)

•Continuous operation with power supply, car voltage or integrated accumulator during transport

•Operation with batteries up to 5 hours (at 22 °C ambient temperature)

•For use with 8 x 13 ml Falcon tubes (REF 13881) or 2 x 13 ml and 8 x 5 ml Falcon tubes (REF 16518)

•Compact design

Dimensions 111 x 111 x 215 mm (w x d x h)

Weight    2.4 kg

Power supply 100 - 240 V AC, 50/60 Hz

Temperature Between 32 °C and 42 °C available

(to be advised before order)

Accuracy of regulation ± 0.3 °C

Heating up time 22 °C to 37 °C approx. 1 h*

Operation time With power supply or 12 V car voltage continuously

With accumulator approx. 5 h*

Charging time of accumulator Approx. 3 h*

Heating block For use with 8 x 13 ml Falcon tubes (REF 13881) or 2 x 13 ml and 8 x 5 ml Falcon tubes (REF 16518)

*at 22 °C ambient temperature

Independent measuring device for control and evaluation of CO2, temperature and O2

Accurate measuring of CO2, temperature and optional O2

Single or continuous measurement in arbitrary intervals

Measurement and documentation of multiple incubators

Documentation of measurements with date, time and incubator number

Easy menu navigation

Data-Download via USB; PC software DataVISUAL`09 incl.

Continuous operation by Li-Ion battery or mains adapter possible

Case Plastic (ABS)

CO2 measurement Dual beam infrared sensor

Range: 0 - 10 % CO2

Display definition: 0.1 % CO2

Accuracy:

0 - 6 % CO2 ± 0.2 % CO2

6 % - 10 % CO2 ± 0.3 % CO2

Sample volume per measurement (2 min.): approx. 0.8 l

Temperature measurement Platinum temperature sensor PT1000

Range: 0 - 100 °C

Display definition: 0.1 °C

Accuracy:

20 °C - 50 °C ± 0.2 °C

50 °C - 100 °C ± 0.3 °C

O2 measurement Galvanic sensor

Range: 0 - 100 % O2

Display definition: 0.1 % O2

O2 sensor not included

Data logger

Recording of measurement logging in arbitrary intervals

Output of measurements via:

backlit LCD

PC software Data Visual’09 (via USB data cable)

Interval for data logging: 15 - 120 min., adjustable in steps of 5 min.

Storage of max. 1008 measurements with date and time

Power supply Rechargeable Li-Ion battery

Power supply 100 – 240 V AC, 5 V DC 1.5 A

Operation time Use of rechargeable battery approx. 4 h

Time to recharge battery approx. 4 h

Advantages:

Temperature control between 27 °C and 45 °C

Homogeneous temperature distribution

Planar surface for optimal heat transfer to heating blocks, culture dishes and slides

Easy to clean glass surface

Short heating up time

Extremely flat with bigger work surface

Space saving due to separate control unit

Dimensions 420 x 300 x 23 mm (w x d x h)

Weight    5.5 kg

Temperature Adjustable between 27 °C and 45 °C

Heating up time < 15 min.

Power supply 100 – 240 V AC, 50/60 Hz, 140 W

Classification Protection class IPX1 (Hot Plate)

Protection class IPX0 (Controller)

Safety class I

Cable length

Between Controller and Hot Plate 1.5 m

​Advantages:Robust and planar glass surfaceHomogeneous temperature distributionOLED display for intuitive and easy-to-use user menuFunctional buttons with haptic feedback via vibration (disengageable)Extremely flat and space savingCleaning and disinfection with all common detergents

Dimensions 300 x 210 x 15 mm (w x d x h)

Usable surface area 255 x 140 mm

Weight    1050 g (w/o mains adapter)

Temperature stability ±0.2 °C

Temperature homogeneity ±0.3 °C

Temperature Adjustable between 27-45 °C (2 °C above ambient temperature)

Heating up time Approx. 10 min.

Power supply 100 – 240 V AC, 60 W

Cable length Hotplate to mains adapter 1.8 m, mains adapter to plug 1.8 m